• <tt id="yu24o"><input id="yu24o"></input></tt> <tt id="yu24o"></tt>
  • <samp id="yu24o"><label id="yu24o"></label></samp>
  • <blockquote id="yu24o"><nav id="yu24o"></nav></blockquote>
  • <optgroup id="yu24o"></optgroup>
  • <input id="yu24o"><samp id="yu24o"></samp></input>
  • 咨詢熱線
    當前位置: 首頁 > 新聞中心 > 公司動態 >

    車庫門廠家教您如何自行調整行程距離

    發布人:http://www.al-watany.com    發布時間:2021-09-27 10:26:27

    自動車庫門行程的設置可以完成車庫門開關門行程限位的確定,并自動實現開關門過程中力量的檢測和力量的默認選定。行程距離不準確會影響到電動車庫門正常使用,為了節省人力、財力,不少人會通過自己動手來進行調整,下邊車庫門廠家教您如何自行調整行程距離的方法。
    The setting of automatic garage door stroke can determine the limit of garage door opening and closing stroke, and automatically realize the detection and default selection of force in the process of opening and closing. The inaccurate travel distance will affect the normal use of the electric garage door. In order to save manpower and financial resources, many people will adjust it by themselves. The garage door factory below teaches you how to adjust the travel distance by yourself.
    按下控制板上的Func鍵,此時運行燈開始閃爍,按住該鍵超過8秒,運行燈正常亮,此時程序進入開合行程和過載學習過程;
    Press the func key on the control board, and the operation light starts to flash. Press and hold the key for more than 8 seconds, and the operation light is normally on. At this time, the program enters the opening and closing stroke and overload learning process;
    濟南車庫門
    按Inc鍵。這時,馬達開始朝著開門的方向運轉。按住鍵。馬達從低速運轉到高速。同時,運行指示燈閃爍,表示電機向上運行。當您到達理想位置時,松開按鈕,電機停止運行;如果按DEC鍵,電機從緩慢至快速運行,以關閉車門,且STA燈閃爍。用這兩個按鈕來調整上面的位置。
    Press the Inc key. At this time, the motor starts to run in the direction of opening the door. Press and hold the key. The motor runs from low speed to high speed. At the same time, the operation indicator flashes, indicating that the motor runs upward. When you reach the ideal position, release the button and the motor stops running; If the DEC key is pressed, the motor runs from slow to fast to close the door, and the sta light flashes. Use these two buttons to adjust the position above.
    如果位置調整適當,按func鍵一次,則運行指示符將閃爍并關閉,指示上面的學習完成;同時,STA指示燈亮,節目進入下一步學習過程;
    If the position is adjusted properly, press func once, the operation indicator will flash and close, indicating that the above learning is completed; At the same time, the sta indicator light is on, and the program enters the next learning process;
    用Inc和Dec兩個鍵調整下位置。到達預定位置后,按一次func鍵,此時sta燈閃爍,表示下位學習完成;
    Use the Inc and dec keys to adjust the lower position. After reaching the predetermined position, press the func key once. At this time, the sta light flashes, indicating that the lower learning is completed;
    在門體的運行過程中,該程序在門體的運行過程中自動測量門體的阻力。在到達適當位置后,程序自動停止,在一段時間的延遲之后,程序自動關閉門,此時,STA燈點亮,程序測量關門時的強度,到達適當位置后,程序自動停止;
    During the operation of the door body, the program automatically measures the resistance of the door body during the operation of the door body. After reaching the appropriate position, the program will automatically stop. After a period of delay, the program will automatically close the door. At this time, sta light will be on, and the program will measure the strength when closing the door. After reaching the appropriate position, the program will automatically stop;
    力量學習完成后,保存所有學習值,run和sta燈多次閃爍,表示程序學習完成;
    After the strength learning is completed, save all learning values, and the run and sta lights flash for many times, indicating that the program learning is completed;
    此時按遙控上的按鈕或墻上開關上的按鈕,電機就會按要求運行。
    At this time, press the button on the remote control or the button on the wall switch, and the motor will run as required.
    上一篇:車庫門卷簾、翻板兩種類型介紹
    下一篇:茗鑫門業介紹卷簾門的設置要求
    產品中心
    聯系我們