• <tt id="yu24o"><input id="yu24o"></input></tt> <tt id="yu24o"></tt>
  • <samp id="yu24o"><label id="yu24o"></label></samp>
  • <blockquote id="yu24o"><nav id="yu24o"></nav></blockquote>
  • <optgroup id="yu24o"></optgroup>
  • <input id="yu24o"><samp id="yu24o"></samp></input>
  • 咨詢熱線
    當前位置: 首頁 > 新聞中心 > 公司動態 >

    濟南卷簾門電機的安裝步驟及保養

    發布人:http://www.al-watany.com    發布時間:2021-08-30 16:06:26

    電動卷簾門電機是很多自動化家裝喜歡的裝修方式,在現代家居中一般都喜歡用到,那么電動卷簾門電機是怎么安裝的?一起看看本文吧!
    Electric roller shutter motor is a favorite decoration method of many automated home decoration. It is generally used in modern home. How is the electric roller shutter motor installed? Let's take a look at this article!
    一、先在需要安裝的門框框口位置畫出線。表明尺寸大小,然后找工作人員設計出合適的電動卷簾門,這里要注意的一點是框內高度比門扇的高度要高一點點。
    1、 Draw the outgoing line at the door frame opening to be installed. Indicate the size, and then find the staff to design a suitable electric rolling shutter door. What we should pay attention to here is that the height in the frame is a little higher than that of the door leaf.
    二、先把濟南電動卷簾門的門框固定,這里要先拆掉門框下部的固定板。(注意:洞口兩側地面要預留凹槽,經校正合格后,固定木楔,門框鐵腳與預埋鐵板件焊牢。用水泥砂漿或強度不低于10MPa細石混凝土嵌塞牢固即可。)
    2、 First fix the door frame of Jinan electric rolling shutter door. Here, first remove the fixing plate at the lower part of the door frame( Note: grooves shall be reserved on the ground on both sides of the hole. After correction, fix the wooden wedge, and weld the iron foot of the door frame with the embedded iron plate. Cement mortar or fine aggregate concrete with strength not less than 10MPa can be used to plug firmly.)
    三、安裝濟南卷簾門主體門扇。一定要保證卷簾門與墻體結成整體,封閉性要做好,再粉刷洞口及墻體。粉刷完畢后,門縫應均勻平整,開啟電動卷簾門應該自 由輕便,不得有過緊、過松和反彈現象。
    3、 Install the main door leaf of Jinan rolling shutter door. Make sure that the rolling shutter door is integrated with the wall, and the sealing shall be done well, and then paint the hole and wall. After painting, the door seam shall be even and flat, and the opening of the electric rolling shutter door shall be free and light without too tight, too loose and rebound.
    接下來為大家介紹一下卷簾門的保養事項
    Next, let's introduce the maintenance of rolling shutter door
    1、檢查濟南卷簾門的支位偏差及螺絲松緊情況,檢查皮帶的松緊情況,檢查控制器對電機輸出清潔機箱內部的油污、灰塵檢查及自動電動門各部件的磨損情況、高速門、開關門寬度、速度、制動等情況檢查電壓參數是否正常維修、更換損壞的部件,業主還需注重自動門的定期保養與維護,自動門由于受安裝質量及使用環境的影響,使用過程中難免會發生問題。
    1. Check the support deviation and screw tightness of Jinan roller shutter door, check the tightness of the belt, check the controller to clean the motor output, check the oil and dust inside the chassis, check the wear of various parts of the automatic electric door, high-speed door, opening and closing width, speed, braking, etc., check whether the voltage parameters are normal, repair and replace the damaged parts, The owner also needs to pay attention to the regular maintenance of the automatic door. Due to the influence of installation quality and use environment, problems will inevitably occur in the use process of the automatic door.
    2、如果長期缺乏保養,導致電動卷閘門存在的隱患及小故障沒有及時處理,馬達到一定運行電流后做正向運行,將動力傳給同步帶,再由同步帶將動力傳給吊具系統使門扇開啟;門扇開啟后由控制器作出判斷,如需關門,通知馬達作反向運動,關閉門扇。這些小故障逐漸變成大故障,可能導致自動電動門的癱瘓。感應探測器探測到有人進入時,將脈沖信號傳給主控器,主控器判斷后通知馬達運行,同時監控馬達轉數,以便通知馬達在一定時候加力和進入慢速運行。
    2. In case of long-term lack of maintenance, the hidden dangers and small faults of the electric rolling gate are not handled in time. After the motor reaches a certain operating current, it runs in the forward direction, transmits the power to the synchronous belt, and then the synchronous belt transmits the power to the spreader system to open the door leaf; After the door leaf is opened, the controller makes a judgment. If it is necessary to close the door, inform the motor to move in the opposite direction and close the door leaf. These small faults gradually become major faults, which may lead to the paralysis of the automatic electric door. When the induction detector detects someone entering, it transmits the pulse signal to the main controller. After judgment, the main controller notifies the motor to run, and monitors the number of revolutions of the motor, so as to inform the motor to apply force at a certain time and enter slow operation.
    上一篇:濟南卷簾門廠產品的電動裝置是怎樣配置
    下一篇:電動卷簾門行業發展方向何如創新?
    產品中心
    聯系我們